Molslinjen has chosen AYK Energy of Andorra to supply the battery systems for its three new electric fast ferries on the Kattegat. When the first vessel enters service in 2028, it will carry a battery roughly 700 times larger than a typical electric car pack and charge at a power level that makes the biggest car chargers look small. The deciding factor was weight, which AYK Energy has cut by about 300 tonnes.

What are the key figures of Molslinjen’s electric ferries?

The ferries combine a 55,000 kWh battery of about 400 tonnes, charging at up to 54 MW in about 30 minutes, with 129 metres of length, space for 500 cars and nearly 1,500 passengers, and a service speed above 40 knots. The table below lists each figure.

Specification Molslinjen electric ferry
Battery capacity About 55,000 kWh
Battery weight About 400 tonnes (was above 700)
Battery chemistry LFP
Maximum charging power 54,000 kW (54 MW)
Charging time About 30 minutes
Energy per crossing 27,000 to 28,000 kWh
Length 129 metres
Capacity Nearly 1,500 passengers and 500 cars
Speed Over 40 knots (about 74 km/h)
Builder Incat, Tasmania
First service First quarter of 2028

How big are the batteries on Molslinjen’s new electric ferries?

Each of the three ferries will carry a battery system of about 55,000 kWh, equal to the packs in nearly 700 electric cars with 80 kWh each. The supplier is AYK Energy of Andorra, and the packs use LFP chemistry, the same basic type found in many Tesla and BYD models.

LFP is known for a long service life and relatively high thermal stability. It is generally less likely to develop violent heat in a fault than some other lithium ion chemistries. Safety was a central requirement for Molslinjen, and according to chief executive Carsten Jensen it weighed almost as much as battery weight in the choice of supplier. AYK Energy has developed dedicated solutions to limit overheating and to fight any fire inside the battery systems.

How fast can the ferries charge?

Charging power reaches up to 54,000 kW, or 54 MW, which matches 216 Teslas each taking 250 kW at the same moment. A turnaround charge is planned to take about 30 minutes, enough to replace the 27,000 to 28,000 kWh that one crossing is expected to use.

A single crossing therefore consumes roughly half of the total battery capacity. To deliver such output without overloading the grid, large battery storage systems will be built on land in both Aarhus and Sjællands Odde. They will draw power from the grid over time and release it at full force when a ferry docks.

The process is fully automatic. Lasers help position the vessel correctly, and a charging connector is then attached to the ship without manual handling.

Why did the battery weight matter so much?

Weight decides how much energy a fast ferry needs to hold its speed. AYK Energy cut its battery system from more than 700 tonnes to about 400 tonnes, a saving of roughly 300 tonnes, without losing capacity or power. That reduction was the main factor in Molslinjen’s choice of supplier.

When Molslinjen began surveying the market almost two years ago, the AYK Energy system was still above 700 tonnes. The weight loss comes from new battery cells, a lighter aluminium structure and production methods borrowed from the car industry. According to Jensen, the combined weight of ship and batteries is decisive for sailing vessels of this size at high speed. The heavier the ship, the more energy it takes to keep its pace, so hundreds of extra tonnes of batteries can decide whether an electric fast ferry is practical at all.

How fast and how big will the new Kattegat ferries be?

The three catamarans are 129 metres long and are planned to carry nearly 1,500 passengers and 500 cars at over 40 knots, about 74 km/h. That is roughly the speed of today’s diesel fast ferries between Jutland and Zealand, but without diesel.

Passengers should notice less engine noise and vibration than on the current diesel vessels. The vehicle deck is also reorganised: cars will drive on at one end and off at the other, which should speed up boarding and unloading.

When will the electric ferries enter service?

Incat builds the ferries in Tasmania. The first is expected in Denmark at the end of 2027 and should enter service in the first quarter of 2028, with the second following in 2028 and the third in 2029. Together they will replace the diesel fast ferries on the Kattegat.

Once all three are running, one of Denmark’s busiest ferry connections will be fully electric.

Frequently asked questions

How much energy will one crossing use?

Molslinjen expects one crossing to need between 27,000 and 28,000 kWh, roughly half of the 55,000 kWh battery capacity.

Which battery chemistry will the ferries use?

AYK Energy has chosen LFP batteries, the same basic chemistry used by Tesla, BYD and other car makers. LFP is known for long life and relatively high thermal stability.

Where will the ferries be charged?

Charging takes place in Aarhus and at Sjællands Odde, where large shore battery systems will supply up to 54 MW. Charging is automatic, with lasers guiding the ship into position.

Who supplies the batteries and who builds the ferries?

AYK Energy of Andorra supplies the battery systems, and the ferries are built by Incat in Tasmania.

Shares:

Related Posts